How to Clean Moss, Algae, and Mildew Off Decks and Patios
Clean green and black growth off wood, composite, concrete, pavers, and stone without damaging them, keep wash water out of storm drains, and slow regrowth.
The short answer
Sweep off debris, then scrub with a stiff or soft brush (whichever the decking maker specifies), water, and a mild soap or a deck cleaner made for your surface, following the label. Use a pressure washer only within the manufacturer's limits, and direct the wash water onto lawn or garden beds rather than into a storm drain.
- Match the method to the surface. Trex says some of its newer composite lines tolerate gentle pressure washing up to 3,100 psi with a fan tip at least 8 inches away, while TimberTech says to use a power washer for rinsing only, at no more than 1,500 psi, and Trex warns against pressure washing its early-generation boards at all.
- Start gentle. Sweeping, a brush, water, and mild soap remove most green film on composite and stone; stronger cleaners come next, one product at a time, following the label.
- On wood, the USDA Forest Products Laboratory says to keep power-washer pressure low to avoid damaging the wood.
- Most Seattle storm drains empty directly into lakes, rivers, and Puget Sound without treatment. King County's guidance is to send deck and patio wash water to lawn, gravel, or landscaping, and never to send soapy or chemical wash water to a storm drain.
- Growth comes back where surfaces stay shaded, damp, and dirty. Clean in spring and fall, clear debris, trim plants for air and light, and keep gaps and drainage open.
To clean moss, algae, and mildew off a deck or patio, sweep away debris, scrub with water and a mild soap or a cleaner made for that surface, rinse thoroughly, and send the runoff onto a lawn or garden bed instead of the street. Use a pressure washer only within the limits your surface maker sets, which vary a lot: one composite maker allows up to 3,100 psi on some lines, another says 1,500 psi for rinsing only, and wood needs low pressure to avoid damage. This guide covers each common surface, a gentle-to-strong method ladder, the storm drain rules that apply around Seattle, and how to slow the regrowth.
A note on scope: this is exterior home care. Sweepless in Seattle, which publishes this guide, cleans home interiors and does not offer deck or patio cleaning.
Why decks and patios go green here
Seattle’s climate is close to ideal for surface growth. NOAA’s 1991-2020 normals for Sea-Tac show 39.34 inches of precipitation a year spread over about 156 days with measurable rain, so outdoor surfaces stay damp for much of the fall, winter, and spring.
The USDA Forest Products Laboratory describes mildew as fungi that discolor wood and finishes with black deposits, often growing alongside algae, which shows up green. It notes mildew is most common in shaded, moist, or protected areas, such as behind trees or shrubs where air movement is restricted. Trex makes a related point about composite decking: when pollen and dirt sit on the surface for a long time, mold can feed on that film. In other words, the growth is usually living on dirt and moisture, and removing the dirt is half the job.
What you are likely to see:
- Green film on boards and pavers, slick when wet: usually algae.
- Black specks or blotches, especially on wood and in shady corners: usually mildew.
- Green cushions in the gaps between pavers, boards, and stones: moss.
Know your surface first
Check what you have before you buy anything. Composite decks look alike but have very different care rules, so find the brand and product line (on your purchase records, the builder’s paperwork, or a board’s underside or end) and read that maker’s care guide.
| Surface | Gentle method | Pressure washing | Cautions |
|---|---|---|---|
| Wood (cedar, pressure-treated) | Sweep, then scrub with water and a mild detergent or a labeled deck cleaner | Low pressure only, per the USDA Forest Products Laboratory | Test any cleaner on a hidden spot; let wood dry fully before refinishing |
| Composite, newer capped lines (example: Trex Transcend, Enhance, Select) | Hose, warm soapy water, soft-bristle brush, rinse thoroughly | Trex: up to 3,100 psi, fan tip, at least 8 inches from the surface | Dirty water left to dry leaves a film; bleach or acid lightens Trex |
| Composite, early-generation (example: older Trex lines) | Composite deck cleaner, twice a year | Trex: not recommended; voids warranty for resulting damage | No sanding |
| Capped composite and PVC (example: TimberTech) | The maker’s deck cleaner, rinse with a hose | Rinsing only, up to 1,500 psi, fan tip, along the grain | No stiff natural-fiber brush, which can dull the surface |
| Concrete | Sweep, then stiff brush with water and mild detergent | Follow the washer’s manual; start low and test a corner | Keep wash water off the street and out of drains |
| Concrete or clay pavers | Sweep joints, brush with water and mild detergent | Low pressure, nozzle angled away from the joints | Watch that joint sand is not blasted out |
| Natural stone (flagstone, slate, bluestone) | Flush with clear water; mild, non-acidic cleaner | Low pressure, test first | Acids such as vinegar can etch calcium-based stones |
Trex and TimberTech are named here because their care guides are public and specific, not as a recommendation. If your decking is another brand, its guide is the one that counts.
The method ladder: start gentle, step up only if needed
Work up this ladder one step at a time. Most green film on composite and stone never needs to go past step 3.
Step 1: Dry cleanup
Sweep or rake off leaves, needles, and loose debris, and clear the gaps between boards with a putty knife or a deck gap tool. King County’s guidance for washing docks recommends exactly this order: dry methods such as scraping and sweeping first, so less debris ends up in the wash water and you need less cleaner. Bag the debris for the garbage or yard waste.
Step 2: Water and a brush
Wet the surface with a garden hose and scrub. Trex’s care guide calls for warm soapy water and a soft-bristle brush on its newer lines, working dirt out of the embossed grain. TimberTech warns against stiff natural-fiber brushes on its composite boards. Wood, concrete, and stone tolerate a stiffer brush.
Step 3: Mild soap or detergent
For mold and mildew on composite, Trex recommends a hose, warm soapy water, and a soft-bristle brush to remove both the mold and the film it feeds on. The Natural Stone Institute suggests flushing outdoor stone patios with clear water before using any stronger product. Mix only what you need in a bucket and scrub the worst areas first.
Step 4: A cleaner made for the surface
If soap is not enough, use a cleaner labeled for your material. TimberTech names its own deck cleaner and, for some older products, a short list of composite cleaners including an oxygen-action cleaner. The USDA Forest Products Laboratory says mildew on wood can be removed with a commercial cleaner, scrubbed gently with a bristle brush or sponge, then rinsed thoroughly. The Natural Stone Institute lists a mild bleach solution for algae and moss on outdoor stone.
Whatever you choose:
- Read the whole label, and follow its dilution, dwell time, and rinsing directions.
- Test it on an out-of-the-way spot first. Trex notes that products containing bleach or acid will lighten its decking.
- Use one product at a time. Washington’s Department of Health warns never to mix bleach with ammonia, acids, or other cleaners. Our guide to cleaners and what never to mix explains why.
- Do not let cleaner dry on the surface. TimberTech warns that letting its cleaner dry leaves a white film that is hard to remove, and advises cleaning in small sections, rinsing each before moving on, and avoiding direct sun.
- Plan where the rinse water goes before you start (see the storm drain section below).
Step 5: A pressure washer, within limits
A pressure washer is a rinsing and loosening tool, not a first resort, and the limits are set by the surface:
- Composite: follow your maker exactly. Trex allows a pressure washer of no more than 3,100 psi, with a fan attachment, held no closer than 8 inches, on its Transcend, Enhance, and Select lines, and says higher pressure could damage the boards and void the warranty. It does not recommend pressure washing its early-generation decking at all. TimberTech allows a power washer for rinsing only, at up to 1,500 psi with a fan tip, spraying along the grain pattern, never across the width of the board.
- Wood: the USDA Forest Products Laboratory advises keeping power-washer pressure low to avoid damaging the wood. King County’s dock guidance makes the same point about light pressure, warning that excessive pressure can damage the surface and send paint flakes and other material into the water.
- Old paint: if a surface may have lead or other heavy-metal paint, King County says to hire a commercial service that collects and disposes of the wash water properly.
Read your pressure washer’s operator manual before you use it, and keep the spray away from people, pets, windows, and siding. Start with the widest fan tip, hold it well back from the surface, and test on an inconspicuous area.
Step 6: Know when to stop
Stop cleaning and call for repairs or a professional if boards are soft or spongy, fasteners are loose, finish is peeling away in sheets, stone is flaking, or the stain is under a finish where cleaner cannot reach it. Those are carpentry, refinishing, or masonry problems, not cleaning problems.
Keep wash water out of storm drains
This is the part of deck and patio cleaning most people get wrong, and around Seattle it matters.
Why it matters
Seattle Public Utilities says most of Seattle’s storm drains empty directly into local water bodies such as Lake Washington, the Duwamish River, and Puget Sound, meaning pollutants often travel untreated into the environment. Washington’s Department of Ecology says stormwater is not always treated even when it flows into street drains, and can be a leading threat to water quality. SPU makes the same point about washing a car on a driveway: the soap and grime go straight into a nearby storm drain connected to a lake, stream, or the Sound.
What King County tells residents to do
King County’s Stormwater Pollution Prevention Manual has a residential sheet on home maintenance that speaks directly to this job:
- Water from washing decks, driveways, roofs, or other hard surfaces may contain suspended solids and other pollutants and should not be discharged directly to storm drains.
- Redirect wash water to vegetated areas or to gravel, lawn, landscaping, or bare soil where it will soak in slowly. If you cannot, filter it through filter fabric or similar material to catch solids first.
- If you use any chemicals, soaps, or detergents, collect the wash water and pour it down a sink or toilet, or let it soak in on site. Do not send it to a storm drain or surface water.
- If you use moss control or another chemical while washing a roof, disconnect the downspouts so it does not reach the drainage system.
The manual also reminds homeowners that they are responsible for making sure hired contractors follow these practices.
Seattle specifics
Seattle Public Utilities treats soapy or muddy water leaked onto the ground as a spill, a public hazard that rain can carry into the drainage system. If you see a spill reaching a drain, SPU’s Operations Response Center takes reports 24 hours a day at (206) 386-1800, and other water pollution concerns go to (206) 684-7587.
A practical setup
- Before you start, find the nearest storm drain, yard drain, or downspout connection, and note which way the surface slopes.
- Clean small sections and push the water toward a lawn, bed, or gravel strip, not toward the driveway or street.
- If the surface drains only toward pavement, cover a nearby drain temporarily while you work (King County suggests temporarily blocking drains when washing docks) and pick up the water with a wet vacuum to empty into a sink or toilet.
- Use the least cleaner and the least water that does the job.
Slip safety while you work
Algae-covered boards and pavers are slippery when wet, and a freshly washed surface is wetter still. Wear shoes with grippy soles, work from the far end of the deck back toward the stairs or door so you are not walking on what you just cleaned, keep cords and hoses out of walking paths, and close the deck to children and pets until it dries. On raised decks and steps, do not lean over railings with a pressure wand. If a section stays slick after cleaning, scrub it again rather than living with it.
Prevention: slowing the regrowth
You cannot change Seattle’s rain, but you can change how long a surface stays damp and dirty.
A seasonal routine
| When | Task |
|---|---|
| Early spring | Full clean using the ladder above; check boards, fasteners, and finish |
| Spring to summer | Sweep weekly in pollen season; rinse off spills promptly |
| Late summer (dry weather) | Refinish or seal wood if the finish maker’s instructions call for it |
| Early fall | Second full clean before the wet season; clear gaps and drains |
| Late fall to winter | Sweep or rake leaves and needles off whenever they pile up |
Trex recommends spring and fall cleaning for its early-generation decking to stop pollen and debris building up, which supports mold growth.
Sun, air, and drainage
- Trim back plants. The Forest Products Laboratory notes mildew thrives where trees or shrubs restrict air movement and surfaces stay damp. Opening up even a little light and airflow helps.
- Keep gaps open. Clear the spaces between deck boards and the joints between pavers so water drains through instead of sitting on top.
- Move things around. Planters, mats, and furniture that stay in one spot all winter trap moisture underneath.
- Mind the gutters and downspouts. Water spilling onto a deck or patio from a clogged gutter keeps that corner permanently wet.
Sealing and finishing
Sealing applies to wood and some masonry, and only by the product’s instructions. The Forest Products Laboratory says to refinish cleaned wood once it is dry, using a finish that contains a mildewcide. Composite and capped decking usually needs no sealing; check the maker’s guide before applying anything.
For the indoor side of the same problem, see our guides to mildew on window sills and keeping your home clean in the rainy season, which covers mud and grit tracked in from outside.
Worked example: a shaded cedar deck (illustrative)
The following is an illustrative scenario, not a real project or a measurement.
Consider a 1990s house in West Seattle with a cedar deck on the north side, under a big Douglas fir. By March, the boards nearest the house are dark with black mildew specks, the gaps are packed with needles, and a green film makes the steps slick.
- Check the surface. The boards are firm and the finish is worn but not peeling. No old paint is involved.
- Plan the water. The deck slopes toward a lawn on one side and a concrete path to the driveway on the other. The owners will push all wash water toward the lawn and lay a towel barrier across the path end.
- Dry cleanup. Sweep, then clear every gap with a deck gap tool. The needles go in the yard waste cart.
- Scrub. A stiff brush and a bucket of water with mild detergent take off most of the green film. The black specks remain on the shadiest boards.
- Step up once. They use a cleaner labeled for wood decks on those boards only, following the label’s dwell time, then rinse with a garden hose. No pressure washer is needed.
- Prevention. They have an arborist thin the lower fir branches, move two planters off the deck for the winter, and plan to refinish with a mildew-resistant product in a dry stretch of August, per the product’s instructions.
In this scenario, the steps stop being slippery, and the twice-a-year cleaning keeps the deck manageable from then on. For how outdoor work fits a broader home schedule, see how often to deep clean.
When to hire someone
Consider an exterior cleaning company or contractor when the deck is high off the ground or has many stairs, the surface is large, the decking type is unknown and you do not want to risk a warranty, there is old paint that could contain lead, or repairs are needed. Ask any company you hire what pressure and cleaners it uses on your surface, whether it follows the decking maker’s limits, and how it will keep wash water out of storm drains. King County reminds homeowners that they share responsibility for making sure contractors follow its stormwater practices.
Common questions
Is it ever fine to let deck wash water run into the street?
Not if it carries soap, cleaner, or much grit. King County's residential guidance says water from washing decks and other hard surfaces should not go directly to storm drains, and that wash water with any soap or chemical must be collected for a sink or toilet or soaked into the ground on site. Seattle Public Utilities counts soapy or muddy water reaching the ground as a spill.
Should I use bleach on my patio?
Only if the surface maker allows it, and never mixed with anything. The Natural Stone Institute lists a mild bleach solution for algae on outdoor stone, but Trex says bleach or acid products will lighten its decking. Bleach is also exactly the kind of chemical King County says must not reach a storm drain. Washington's Department of Health warns never to combine bleach with ammonia, acids, or other cleaners.
How often should a Seattle deck be cleaned?
Trex recommends cleaning its early-generation composite twice a year, in spring and fall, to stop pollen and debris from feeding mold. Twice a year is a reasonable baseline for most decks and patios here, with quick sweeps in between whenever leaves or needles pile up.
Will a pressure washer void my composite deck warranty?
It can. Trex says using a pressure washer over 3,100 psi could damage its boards and void the warranty, and that any pressure washing of its early-generation decking voids the warranty for damage it causes. Check your own decking line's care guide before you start.
Does Sweepless in Seattle clean decks or patios?
No. Sweepless in Seattle, which publishes this guide, cleans home interiors. For exterior surfaces, look for an exterior cleaning or pressure washing company and ask how it handles wash water.
Sources and references
- How to Clean Composite Decking (Care and Cleaning) , Trex Company Accessed November 15, 2026
- Care and Cleaning , TimberTech (AZEK) Accessed November 15, 2026
- Wood Handbook: Wood as an Engineering Material, Chapter 16, Finishing of Wood , USDA Forest Service, Forest Products Laboratory Primary source Accessed November 15, 2026
- Care and Cleaning for Natural Stone Surfaces , Natural Stone Institute Accessed November 15, 2026
- R-6: Residential Home Maintenance and Repair (Stormwater Pollution Prevention Manual) , King County Stormwater Services Primary source Accessed November 15, 2026
- R-9: Residential Dock Washing (Stormwater Pollution Prevention Manual) , King County Stormwater Services Primary source Accessed November 15, 2026
- Storm Drain Care , Seattle Public Utilities Primary source Accessed November 15, 2026
- Report Water Pollution , Seattle Public Utilities Primary source Accessed November 15, 2026
- The Problem with Car Washing , Seattle Public Utilities Primary source Accessed November 15, 2026
- Stormwater and residential pollution , Washington State Department of Ecology Primary source Accessed November 15, 2026
- Dangers of Mixing Bleach with Cleaners , Washington State Department of Health Primary source Accessed November 15, 2026
- Annual/Seasonal Climate Normals 1991-2020, Seattle-Tacoma International Airport (USW00024233) , NOAA National Centers for Environmental Information Primary source Accessed November 15, 2026
See something out of date or wrong? Tell the editors. Read how we work in our editorial policy.